Skip to content
WellDepth

Find a well in Idaho

Search any point in Idaho to see the water well records the state holds nearby: depth, depth to water, yield, and a link to the driller's report for each one. Free, no account. Enter an address, paste coordinates, or click the map: rural addresses often will not resolve, so the last two always work.

type a town, an address, coordinates, or click the map
Loading map…

The highlighted area is Idaho, the only state these well records cover. Basemap: U.S. Geological Survey, National Geospatial Program.

How to read these numbers

Every row is a well someone actually drilled and reported to the state. None of them is on the parcel you are looking at, so treat the set as a picture of the area rather than a prediction.

Total depth

How deep the well was drilled, in feet. Drilling is usually quoted per foot, so the spread between the shallowest and deepest nearby well is a rough budget range. A wide spread over a short distance means the aquifer is uneven and a quote could move a lot.

Depth to water

How far below the surface water stood once the well was finished, the static water level. It drives what pump you need and how much it costs to run. Note that a reading of zero is ambiguous in the state records: it can mean water at the surface, or that nobody wrote a figure down. We exclude zeros and tell you how many we excluded rather than guessing.

Reported yield

What the driller measured the well producing, in gallons per minute. A single household typically needs far less than irrigated pasture or livestock, so read it against your plans. Yield can also change with the season and with how hard the well is pumped.

Why location accuracy matters here

Only about a fifth of Idaho well records have a surveyed location. Most were recorded as a quarter-quarter section, a 40-acre block, so the true well could be up to roughly 900 feet from where it is plotted. We label every row with how it was located, so you can tell which distances to lean on. It is also why some map markers overlap: wells recorded this way share a section corner.

What is missing

The database holds most reports filed since July 1987. Older wells may be missing entirely, and plenty of records have blanks where a depth or yield should be. We show you the count behind every figure, "median depth from 83 of 108 wells", so you can judge how much weight it carries.

Common questions

Where does this well data come from?

From the Idaho Department of Water Resources well log database, which holds the reports drillers are required to file. Records are most complete from July 1987 onward.

How is this different from IDWR's own Find a Well map?

Same records, same source. IDWR is built to show you one well and its report; this shows every water well within a radius of a point, with the median depth, the full range and the number of records behind each figure. One answers "what does this well say"; the other answers "what will a well here cost me".

How deep is my well?

If it was drilled and reported after July 1987, search your address and it should appear in the list with its total depth. Open the driller’s report for the construction detail - casing, formation and the water level the driller measured.

Do I need a well tag number to search?

No. A well tag number is the identifier IDWR assigns a well, and it is useful if you have it, but an address or a click on the map is enough here.

Does this tell me whether I can drill a well on a parcel?

No. It shows what nearby wells found. Groundwater varies over short distances, and only a licensed well driller can tell you what to expect on a specific parcel.

Why do some wells appear stacked in the same spot?

Most Idaho well locations were recorded as a quarter-quarter section, a 40-acre block, rather than a surveyed point. Wells recorded that way share a section centroid, so several can appear at the same place.

What to do with this

  1. Get at least two quotes from licensed Idaho drillers, with a per-foot rate.
  2. Ask your public health district what septic site evaluation the parcel needs.
  3. Have a title company confirm water rights and easements.
  4. Have boundaries and acreage confirmed by a licensed surveyor.